Choose the right solution in a few clicks!

Other devices

Service

Remove FRP for Lenovo smartphones
  1. Power off the phone
  2. Open Qcom tab
  3. Go to "Service" tab
  4. Select your model from “Phone model” drop-down list on the right
  5. Select virtual port “Plug USB cable into the powered off phone…”
  6. Press "Remove FRP" button
  7. Set the phone to EDL mode (for example):
    • Lenovo P1a42: Press vol+ button and insert USB cable
    • Lenovo K53a48: Press vol+ button and insert USB cable. Select Download in the appeared menu
    • Lenovo PB1-750M: Press and hold vol- and vol+ buttons simultaneously and insert USB cable
  8. Connect your phone to PC with USB cable
  9. Message "Done" indicates that the procedure has been completed successfully and device can be disconnected now.
Remove FRP for Qualcomm smartphones using original loaders

It is possible to remove FRP for new Qcom-based smartphones if you have the original loader for it.
In most cases original loaders can be found in the phone’s firmware package.
Typical filename: prog_emmc_firehose.mbn.

  1. Power off the phone
  2. Open Qcom tab
  3. Go to "Service" tab
  4. Select virtual port “Plug USB cable into the powered off phone…”
  5. Select “EDL” and “Loader selection...” in “Phone model” drop-down list on the right
  6. Press "Remove FRP" button and select loader in original format
  7. Set the phone to EDL mode
  8. Connect your phone to PC with USB cable
  9. Message "Done" indicates that the procedure has been completed successfully and device can be disconnected now.

Make sure that the operation was completed successfully and post the successful log with attached loader on the official Sigma forum.

Remove FRP using QCOM AUTODETECT feature
  1. Power off the phone
  2. Open Qcom tab
  3. Go to "Service" tab
  4. Select “EDL” and “Autodetect” in “Phone model” drop-down list on the right
  5. Select virtual port “Plug USB cable into the powered off phone…”
  6. Press "Remove FRP" button
  7. Connect your phone to PC in EDL mode with USB cable. There are different procedures to put a certain phone model in EDL mode: pressing key combinations, EDL cable, etc.
  8. Message "Done" indicates that the procedure has been completed successfully and device can be disconnected now

Unlock

Direct unlock for Bmobile QW130
  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. "Phone model" dropdown box has to be set to "Bmobile QW130"
  4. Connect turned ON phone to PC with USB cable
  5. Install required Bmobile QW130 Driver (only if the phone is connected for the first time); in some cases drivers can be installed automatically
  6. Select USB Diagnostic Port in the ports selection tab
  7. Press "Unlock" button
Direct unlock for SkypePhone AMOI WP-S1 / WP-S2
  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Connect turned ON phone to PC with USB cable
  5. Install required drivers (only if the phone is connected for the first time)
  6. Select USB Diagnostic Port in the ports selection tab
  7. Press "Unlock" button

* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. In the end of heuristic unlock mode procedure, please send the log file to support.

Direct unlock for ZTE hotspot mobile devices

You need to choose the model manually from the "Phone model" list. The list is located near the ports selection menu

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. Select device model from the "Phone model" list
  4. Connect the device to PC with USB cable
  5. Power the device ON
  6. It can take from 30 seconds up to a minute for a device to fully start up
  7. Install required USB driver (only if the device is connected for the first time). Drivers should be installed automatically from the device; make sure that AutoRun feature is enabled on your PC
  8. Select "ZTE Diagnostic interface" in the ports selection tab
  9. Press "Direct Unlock" button
  10. The message "Unlocking phone... Done" indicates that procedure was completed successfully
  11. Wait for the message "Restarting phone... Done" to appear in dialog window; only after that you can disconnect the phone
Direct unlock for BLU Dash 3.5 (D160A) / Tecno P3
  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Turn the phone on without sim card
  5. Connect the phone to PC with USB cable
  6. Install USB Host Driver
  7. Select Qualcomm DIAG (Diagnostic) Port in the ports selection tab
  8. Press "Unlock" button
  9. Wait for the message "Restarting phone... Done" to appear in dialog window; only after that you can turn the phone off
Direct unlock for Kyocera C6522, C6530, E6560, E6710, E6790TM
  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect" or "Kyocera Android"
  3. Go to "Unlock" tab
  4. Turn the phone on without SIM-card inserted
  5. Dial ##3424# and enter 000000 (6-digit MSL code). Select Diag -> enable
    Alternatively, MSL-code can be read using Kyocera MSL Reader. You can find it at Android Market.
  6. Connect the phone to PC with USB cable
  7. Install the required USB Driver
  8. Select  Diagnostic Port / KYOCERA USB KC02US Serial Port in the ports selection tab
  9. Press "Unlock" button
  10. Wait for the message "Restarting phone... Done" to appear in dialog window; only after that you can turn off the phone
Get unlock codes for Kyocera C6522
  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Turn the phone on without SIM-card inserted
  5. Dial ##3424# and enter 000000 (6-digit MSL code). Select Diag -> enable
    Alternatively, MSL-code can be read using Kyocera MSL Reader. You can find it at Android Market.
  6. Connect the phone to PC with USB cable
  7. Install the required USB Driver
  8. Select Diagnostic Port / KYOCERA USB KC02US Serial Port in the ports selection tab
  9. Press "Get unlock codes" button
  10. Wait for the message "Restarting phone... Done" to appear in dialog window; only after that you can turn off the phone
  11. The code will be shown in the program window
Universal unlocking manual for Qualcomm based device
  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. Set "Autodetect" in the "Phone model" dropdown box
  4. Connect a turned ON phone to a PC with USB cable
  5. Install a required driver.
    • In some cases drivers can be installed automatically from a device. Sometimes you need to find and install a driver by yourself. Usually phone’s manufacturer provides drivers on its web-site.
  6. Select "USB Diagnostic Port" in the ports selection tab
  7. Press "Unlock" button
Video instructions

Repair

Repair IMEI for ZTE hotspot mobile devices

You need to choose the model manually from the "Phone model" list. The list is located near the ports selection menu

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "IMEI" tab
  3. Select device model from the "Phone model" list
  4. Connect the device to PC with USB cable
  5. Power the device ON
  6. It can take from 30 seconds up to a minute for a device to fully start up
  7. Install required USB driver (only if the device is connected for the first time). Drivers should be installed automatically from the device; make sure that AutoRun feature is enabled on your PC
  8. Select "ZTE Diagnostic interface" in the ports selection tab
  9. Enter IMEI number in the "Phone IMEI" field
  10. Press "Repair IMEI" button
  11. The message "Done" indicates that procedure was completed successfully
Repair IMEI for BLU Dash 3.5 (D160A) / Tecno P3
  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Turn the phone on without sim card
  5. Connect the phone to PC with USB cable
  6. Install USB Host Driver
  7. Select Qualcomm DIAG (Diagnostic) Port in the ports selection tab
  8. Enter IMEI number in the "Phone IMEI" field
  9. Press "Repair IMEI" button
  10. The message "Done" indicates that procedure was completed successfully

 

Reminder! Before servicing the phone, please make sure that:

  1. You use the latest version of the software
  2. Battery must be connected to the phone's board and fully charged. Especially while performing operations using testpoint.
  3. All the side programs, that may interfere with the phone, are closed
  4. Phone’s cable and device itself should not be disconnected or disturbed until the procedure is fully completed
  5. Connect phone to USB port placed on the backside of PC (motherboard's USB port)
    Do not connect or disconnect other USB cables into the PC during the actual work with the phone
  6. Avoid using any kind of USB HUBs and long USB cables. Use the shortest-length USB cable available.
  7. Phone has stock (factory) firmware version
  8. SIM card is removed
EN
Subscribe

Here you can subscribe to the newsletters you are interested in

Subscribe

Privacy Policy and Subscription Agreement

Last updated on April 20th, 2018.

Emails and Electronic Communication

We offer you to subscribe to our newsletters. If you no longer wish to receive correspondence, emails, or other communications from us, you may opt-out. To do this click Unsubscribe in newsletters you are receiving from us.

Most of all, we value your privacy. We do not sell, rent, loan, or give your email address or other personal information to anybody without your express permission.

Collection of Information

Here are the types of information we collect:

The information you give us

We receive and store any information you enter on our website or give us in any other way. We use the information that you provide for such purposes as responding to your requests, customizing future shopping for you, improving our service, and communicating with you.

Log data

We collect information that your browser sends whenever you visit our website. This log data may include information such as your computer’s Internet Protocol (“IP”) address, browser type, browser version, the pages of our Site that you visit, the time and date of your visit, the time spent on those pages and other statistics. In addition, we may use third-party services such as Google Analytics that collect, monitor and analyze this type of information in order to increase our Site’s functionality. These third-party service providers have their own privacy policies addressing how they use such information.

When you browse a website on a mobile device, we may collect certain information automatically, including, but not limited to, the type of mobile device you use, your mobile device’s unique device ID, the IP address of your mobile device, your mobile operating system, the type of mobile Internet browser you use, your location information and other statistics.

Cookies

Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a website and stored on your computer's hard drive. Like many sites, we use cookies to collect information. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use some portions of our Site.

We also use tracking information to determine which areas of our site users like and do not like based on traffic to those areas.

Use of Information

We use your personal information for the following purposes: to administer and improve the site and related services, to notify you of our products, services, promotional events or special offers that you may be of interest to you, etc.

Affiliates

We may share your information with our affiliates, in which case we will require those affiliates to honor this Privacy Policy. Affiliates include our parent company and any subsidiaries, joint venture partners or other companies that we control or that are under common control with us.

Security of Information

We are committed to protecting customer personal information. The security of your Personal Information is important to us, and we strive to implement and maintain reasonable, commercially acceptable security procedures and practices appropriate to the nature of the information we store, in order to protect it from unauthorized access, destruction, use, modification, or disclosure. However, please be aware that no method of transmission over the internet, or method of electronic storage is 100% secure and we are unable to guarantee the absolute security of the Personal Information we have collected from you.

Changes to this Privacy Policy

We will occasionally update this Privacy Policy. When we do, we will also revise the "last updated" date at the top of the Privacy Policy.

Decline Accept