Qualcomm

Reminder! Before servicing the phone, please make sure that:

  1. Battery charged more than 50%
  2. All the side programs, that may interfere with the phone, are closed
  3. The phone cable will not be disconnected till the process is done
  4. Connect phone to USB port placed on the back side of PC (motherboard's USB port).
  5. Avoid using any kind of USB HUBS.
  6. Phone has stock (factory) firmware version.

Calculator

Code Calculation Manual

  1. Select "Qualcomm" platform from tab menu in upper left side of the software
  2. Go to "Calculator" tab
  3. Choose desired model from the list of supported
  4. Choose provider ID from the list of available; in most cases "provider ID" of your phone can be found at the sticker under the battery. In case providers ID is not specified on the sticker under the battery, try to find it on the phone's package - it should be mentioned there.
  5. Enter phone's IMEI number
  6. Click "Calculate" button and wait for calculation procedure to start
  7. Unlock codes are calculated

Free distribution of unlock codes calculated by Sigma Software is strictly prohibited! Violation of this policy will result in your card being blocked.

How to enter codes

  1. Turn the phone on with non-original SIM card inserted
  2. Phone's menu will pop-up with unlock code request
  3. Enter a code that was read by Sigma Software

ZTE Phones

Direct Unlock

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect".
  3. Go to "Unlock" tab
  4. Power the phone ON
  5. Connect the phone to PC with USB cable
  6. Install required ZTE handset USB driver (only if the phone is connected for the first time); in some cases drivers can be installed automatically
  7. Select USB Modem port in the ports selection tab
  8. Press "Unlock" button *
  9. The message "Unlocking phone... Done" indicates that procedure was completed successfully
  10. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. Duding the extended heuristic method operation the phone will be restarted, so please wait till the process is completed. In the end of heuristic unlock mode procedure, please send the log file to our support.


** PC connection of the phone has to be set to USB (not Bluetooth)
In phone menu: Settings - Connections - PC connection - USB

Read User Code

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect".
  3. Go to "Unlock" tab
  4. Power the phone ON
  5. Connect the phone to PC with USB cable
  6. Install required ZTE handset USB driver (only if the phone is connected for the first time); in some cases drivers can be installed automatically
  7. Select USB Modem port in the ports selection tab
  8. Press "Get Unlock Codes" button
  9. The message "Reading unlock codes... Done" indicates that procedure was completed successfully
  10. Disconnect the handset

** PC connection of the phone has to be set to USB (not Bluetooth)
In phone menu: Settings - Connections - PC connection - USB

Repair IMEI

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Power the phone ON
  5. Connect the phone to PC with USB cable
  6. Install required ZTE handset USB driver (only if the phone is connected for the first time); in some cases drivers can be installed automatically
  7. Select USB Modem port in the ports selection tab
  8. Enter IMEI number in the "Phone IMEI" field
  9. Press "Restore IMEI"
  10. The message "Done" indicates that procedure was completed successfully
  11. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

** PC connection of the phone has to be set to USB (not Bluetooth)
In phone menu: Settings - Connections - PC connection - USB

Unlocking with heuristic method

In general ZTE phone unlocking lasts several seconds. But what do we do when we stumble on unknown firmware version?


If you'll try to unlock the phone that has an unsupported firmware version, software will prompt you to choose heuristic method of unlocking. In this case, process can take several minutes. If Sigma won't find required for unlock data, it will give you two more available options:


  1. Extended heuristic method of unlocking:
    With this method search process will take a little bit longer. During the operation your phone will restart automatically several times. In some cases you'll be prompted to restart a phone manually.
  2. Read Dump from the phone:
    This option allows you to read Dump from your phone and send it to support. It is highly recommended to close all applications and do not perform any actions with your PC during the dump reading process. Unlocking feature for this firmware version will be added with next updates.

Choose one of them.


Wait till the process will complete. In the end of procedure send the log or DUMP file to support@sigmakey.com

Video instructions

ZTE Android Smartphones

Set smartphone to FTM (Field Test Mode)

Procedure may be different for some types of ZTE smartphones

General procedure:

  1. Switch the device off.
  2. Press Volume Down and Power On buttons simultaneously until you see "FTM" message on the phone's screen.

Alternative way:

  1. Switch the device off.
  2. Press Volume Down, End Call and Power On buttons simultaneously until you see "FTM" message on the phone's screen.

* If you can't enter FTM mode, turn the phone ON, dial *983*87274# and choose "only Diag".


ZTE tablets: V9, V9+, Light Tab 2, Vodafone Smart Tab 7 / 10

  1. Switch the device off.
  2. Press Volume Up and Power On buttons simultaneously until you see "FTM" message on the phone's screen.

Set the smartphone to Download Mode

In order to service some firmware versions of ZTE smartphones, you should connect them in the Download Mode.


Here are some of the versions:

  • T790: ICS_P752A20V1.0.0B09
  • Blade 3:
    • ICS_P772N10_MTSV1.0.0B01
    • ICS_P772N10V1.0.0B12
  • Orange Zali / Kis Pro:
    • ORO_RO_P752D20V1.0.0B02
    • ORO_RO_P752D20V1.0.0B03
  • Open:
    • B2G_P752D04V1.1.0B02_TME
    • B2G_P752D04V1.1.0B13_MOVISTAR

How to set the smartphone to Download Mode

  1. Switch the device OFF
  2. Remove the flash card from the phone
  3. Press and hold down Vol -, Vol + buttons simultaneously, then press and hold Power until your phone completely freezes

Direct unlock

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Install required Android USB Driver Installer (only if the phone is connected for the first time)
  5. Set the phone to "FTM" mode
  6. Connect the phone to PC with USB cable
  7. Select USB Modem port in the ports selection tab
  8. Press "Unlock" button*
  9. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

* ZTE smartphones with old security can have two different lock types, so direct unlock might require two attempts. During unlock procedure you will be asked to select first or second unlocking method. If the chosen method will not unlock your device, try another one.


* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. In the end of heuristic unlock mode procedure, please send the log file to support.

Get unlock codes

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Install required Android USB Driver Installer (only if the phone is connected for the first time)
  5. Set the phone to "FTM" mode
  6. Connect the phone to PC with USB cable
  7. Select USB Modem port Interface in the ports selection tab
  8. Press "Get Unlock Codes" button

For ZTE smartphones Sigma doesn't show unlock codes. It shows Lock Status and a number of available code entry attempts near each type of code.
Closed lock: active unlock code
Open lock: inactive unlock code

Repair IMEI

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Install required Android USB Driver Installer (only if the phone is connected for the first time)
  5. Set the phone to "FTM" mode
  6. Connect the phone to PC with USB cable
  7. Select USB Modem port in the ports selection tab
  8. Enter IMEI number in the "Phone IMEI" field
  9. Press "Restore IMEI" button
  10. The message "Done" indicates that procedure was completed successfully
  11. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Direct unlock for ZTE Startext II / N720 / N721 / V6000 / Vtelca N720/ Style Q / Onda TQ150 / Sfr Starnaute 2

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Connect turned ON phone to PC with USB cable
  5. Install required drivers (drivers will be installed from the phone automatically) only if the phone is connected for the first time
  6. Select USB Diagnostic Port in the ports selection tab
  7. Press "Unlock" button *

Repair IMEI for V889F / V880G / V955 / A2 / Blade G / N881F / N8881E / Blade III Pro + Blade V / V956 / N880F / N880G / N881E / N909

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Set the phone to "Download" mode:
    1. Turn the phone OFF
    2. Press and hold Vol+ Vol- then insert USB cable into the phone
  5. Install required USB Driver Installer (only if the phone is connected for the first time)
  6. Select USB Modem port in the ports selection tab
  7. Enter IMEI number in the "Phone IMEI" field
  8. Press "Restore IMEI"
  9. The message "Done" indicates that procedure was completed successfully
  10. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can disconnect the phone

Direct Unlock procedure for Orange Boston

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown menu has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Set the phone to "Recovery" mode:
    1. Turn the phone OFF
    2. Press Vol + , Camera, Power ON, then insert USB cable into the phone
  5. Install required USB Driver (only if the phone is connected for the first time)
    • If Sigma won't show "modem port" in the ports selection menu, install other drivers
  6. Select USB Modem port in the ports selection tab
  7. Press "Unlock" button
  8. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can disconnect the phone

Heuristic method of unlocking is supported for this group of models.

Wrong Code Counter resets automatically during the direct unlock procedure.

Repair IMEI procedure for Orange Boston

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown menu has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Set the phone to "Recovery" mode:
    1. Turn the phone OFF
    2. Press Vol + , Camera, Power ON, then insert USB cable into the phone
  5. Install required USB Driver (only if the phone is connected for the first time)
  6. Select USB Modem port in the ports selection tab
  7. Enter IMEI number in the "Phone IMEI" field
  8. Press "Restore IMEI" button
  9. The message "Done" indicates that procedure was completed successfully
  10. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Direct Unlock procedure for Orange Nivo

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. Set "Phone model" dropdown to "Autodetect" value
  3. Go to "Unlock" tab
  4. Connect a phone to PC with USB cable
  5. Adjust USB Settings on the phone:
    a. Go to Notifications (by touching the notifications bar at the top of the phone's screen and dragging it down)
    b. touch the USB connection notification
    c. select "media device MTP"
    d. then select "normal NML"
  6. Select "Coolpad Android Diagnostics USB VCOM port"
  7. Press "Direct unlock" button
  8. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that turn the phone off.

Video instructions

Alcatel Android Smartphones

Direct unlock

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect". In case Sigma won't detect Alcatel model automatically, select "Alcatel Android" manually in this dropdown box
  3. Go to "Unlock" tab
  4. Turn the phone on without sim card
  5. Connect the phone to PC with USB cable
  6. Install USB Host Driver
  7. Select Qualcomm DIAG (Diagnostic) Port in the ports selection tab
  8. Press "Unlock" button
  9. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Diagnostic mode activation: dial *#2618#

Direct unlock for Alcatel OT-6034R / OT-6035R

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Turn the phone ON
  5. Connect the phone to PC with USB cable
  6. Adjust USB Settings on the phone:
    a. Go to Notifications (by touching the notifications bar at the top of the phone's screen and dragging it down)
    b. touch the USB connection notification
    c. uncheck all the options (if checked)
  7. Install required USB Driver
  8. Select "Alcatel HS-USB Android DIAG Port" in the ports selection tab
  9. Press "Direct unlock" button
  10. After the operation it is necessary to reset the phone manually

Repair damaged security area

User agreement:
This option is introduced for the advanced users that have clear understanding what they do with the phone during all stages of repair.

  1. Download Repair file for your phone from Sigma section of boot-loader.com website -> Alcatel -> Repair_Files
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. Go to "Service" tab
  4. Turn the phone ON and connect the phone to PC with USB cable
  5. Choose appropriate Repair File (in SKF format)
  6. Press "Repair Security Area" button and wait for the procedure to finish

Get unlock codes

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect". In case Sigma won't detect Alcatel model automatically, select "Alcatel Android" manually in this dropdown box
  3. Go to "Unlock" tab
  4. Turn the phone on without simcard
  5. Connect the phone to PC with USB cable
  6. Install USB Host Driver
  7. Select Qualcomm DIAG (Diagnostic) Port in the ports selection
  8. Press "Get Unlock Codes" button

For Alcatel smartphones Sigma doesn't show unlock codes. It shows Lock Status and a number of available code entry attempts near each type of code.
Closed lock: active unlock code
Open lock: inactive unlock code

Video instructions

Motorola Android Smartphones

Unlock

Direct unlock

  1. Turn the phone on and wait for it to fully start up
  2. Connect the phone to PC with USB cable
  3. Ensure that the phone is not connected in USB mass storage mode
  4. Install Motorola drivers (only if the phone is connected for the first time)
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "Unlock" tab
  8. Press "Connect Motorola Android phone"
  9. Select "Motorola USB Diagnostic Port" in the ports selection tab
  10. Press "Unlock" button
  11. Message "Unlocking phone… Done" indicates that procedure was completed successfully
  12. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Note: You should run Sigma Software as Administrator in order to work with Motorola Android smartphones.


* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. In the end of heuristic unlock mode procedure, please send the log file to support.

Get unlock codes

  1. Turn the phone on and wait for it to fully start up
  2. Connect the phone to PC with USB cable
  3. Ensure that the phone is not connected in USB mass storage mode
  4. Install Motorola drivers (only if the phone is connected for the first time)
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "Unlock" tab
  8. Press "Connect Motorola Android phone" button
  9. Select "Motorola USB Diagnostic Port" in the ports selection tab
  10. Press "Get unlock codes" button
  11. Message "Reading unlock codes… Done" indicates that procedure was completed successfully
  12. Disconnect the handset

How to enter codes:

  1. Turn the phone on with non-original SIM card inserted
  2. Phone's menu will pop-up with unlock code request
  3. Enter a code that was read by Sigma Software

  4. Note: You should run Sigma Software as Administrator in order to work with Motorola Android smartphones.

Direct unlock for XOOM tablets: MZ601, MZ603, MZ605

  1. Install Motorola drivers (only if the phone is connected for the first time)
  2. Turn the device Off
  3. Press Vol+ and Vol- simultaneously, while holding these buttons press Power On and wait until it fully starts up
  4. Connect device to PC with USB cable
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "Unlock" tab
  8. Press "Connect Motorola Android phone". Select "Motorola USB Networking driver" in the ports selection tab.
  9. Press "Unlock" button
  10. Message "Unlocking phone… Done" indicates that procedure was completed successfully
  11. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Get unlock codes for XOOM tablets: MZ601, MZ603, MZ605

  1. Install Motorola drivers (only if the phone is connected for the first time)
  2. Turn the device Off
  3. Press Vol+ and Vol- simultaneously, while holding these buttons press Power On and wait until it fully starts up
  4. Connect device to PC with USB cable
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "Unlock" tab
  8. Press "Connect Motorola Android phone". Select "Motorola USB Networking driver" in the ports selection tab.
  9. Press "Get unlock codes" button
  10. Message "Reading unlock codes… Done" indicates that procedure was completed successfully
  11. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Direct unlock for MB612 / MB853 / MB855 / MB860 / MB861 / MB867, ME860, XT610 / XT882

  1. Install Motorola drivers (only if the phone is connected for the first time)
  2. Turn the phone Off
  3. Connect the phone to PC with USB cable
  4. Turn the phone on and wait for it to fully starts up
  5. Ensure that the phone is not connected in USB mass storage mode
  6. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  7. "Phone model" dropdown box has to be set to "Autodetect"
  8. Go to "Unlock" tab
  9. Press "Connect Motorola Android phone". Select "Motorola USB Networking driver" in the ports selection tab.
  10. Press "Unlock" button
  11. Message "Unlocking phone… Done" indicates that procedure was completed successfully
  12. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Get unlock codes for MB612 / MB853 / MB855 / MB860 / MB861 / MB867, ME860, XT610 / XT882

  1. Turn the phone on and wait for it to fully start up
  2. Connect the phone to PC with USB cable
  3. Ensure that the phone is not connected in USB mass storage mode
  4. Install Motorola drivers (only if the phone is connected for the first time)
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "Unlock" tab
  8. Press "Connect Motorola Android phone". Select "Motorola USB Networking driver" in the ports selection tab.
  9. Press "Get unlock codes" button
  10. Message "Reading unlock codes… Done" indicates that procedure was completed successfully
  11. Disconnect the handset
  12. Phone is unlocked

Direct Unlock procedure for XT500 / XT502 / XT3 / XT5

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown menu has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Set the phone to "Recovery" mode:
    1. Turn the phone OFF
    2. Press Vol + , Camera, Power ON, then insert USB cable into the phone
  5. Install required USB Driver (only if the phone is connected for the first time)
  6. Select USB Modem port in the ports selection tab
  7. Press "Unlock" button
  8. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can disconnect the phone

Heuristic method of unlocking is supported for this group of models.

Wrong Code Counter resets automatically during the direct unlock procedure.

Video instructions

Repair

Repair IMEI

  1. Turn the phone on and wait for it to fully start up
  2. Connect the phone to PC with USB cable
  3. Make sure that the phone is not connected in USB mass storage mode
  4. Install Motorola drivers (only if the phone is connected for the first time)
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "IMEI" tab
  8. Press "Connect Motorola Android phone"
  9. Select "Motorola USB Diagnostic Port" in the ports selection tab
  10. Enter IMEI number in the "Phone IMEI" field
  11. Press "Restore IMEI" button
  12. Message "Done" indicates that procedure was completed successfully
  13. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Note: You should run Sigma Software as Administrator in order to work with Motorola Android smartphones.

Repair IMEI procedure for XT500 / XT502 / XT3 / XT5

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown menu has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Set the phone to "Recovery" mode:
    1. Turn the phone OFF
    2. Press Vol + , Camera, Power ON, then insert USB cable into the phone
  5. Install required USB Driver (only if the phone is connected for the first time)
  6. Select USB Modem port in the ports selection tab
  7. Enter IMEI number in the "Phone IMEI" field
  8. Press "Restore IMEI" button
  9. The message "Done" indicates that procedure was completed successfully
  10. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Repair IMEI for MZ601, MZ603, MZ605

  1. Install Motorola drivers (only if the phone is connected for the first time)
  2. Turn the device OFF
  3. Press Vol+ and Vol- simultaneously, while holding these buttons press Power On and wait until it fully starts up
  4. Connect device to PC with USB cable
  5. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  6. "Phone model" dropdown box has to be set to "Autodetect"
  7. Go to "IMEI" tab
  8. Press "Connect Motorola Android phone". Select "Motorola USB Networking driver" in the ports selection tab.
  9. Enter IMEI number in the "Phone IMEI" field
  10. Press "Restore IMEI" button
  11. Message "Done" indicates that procedure was completed successfully
  12. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Repair IMEI for MB612 / MB853 / MB855 / MB860 / MB861 / MB867, ME860, XT610 / XT882

  1. Install Motorola drivers (only if the phone is connected for the first time)
  2. Turn the phone OFF
  3. Connect the phone to PC with USB cable
  4. Turn the phone on and wait for it to fully starts up
  5. Ensure that the phone is not connected in USB mass storage mode
  6. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  7. "Phone model" dropdown box has to be set to "Autodetect"
  8. Go to "IMEI" tab
  9. Press "Connect Motorola Android phone". Select "Motorola USB Networking driver" in the ports selection tab.
  10. Enter IMEI number in the "Phone IMEI" field
  11. Press "Restore IMEI" button
  12. Message "Done" indicates that procedure was completed successfully
  13. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Video instructions

Huawei Android Smartphones

Connect:

Download Mode

U8667, U8680, U8681, U8730, U8800, U8815, U8816, U8818, U8820, U8825D, U8860, C8860E U8655, U8665, U8666, U8833, U8950, U8950D, U8951, U8951D

  1. Switch the device OFF
  2. Remove the flash card from the phone
  3. Press and hold down Vol -, Vol + buttons simultaneously, then press and hold Power until your phone completely freezes on the pink screen

When the phone is in "Download mode" you need to connect it to computer and install required driver (only if the phone is connected for the first time).

Fastboot mode

Different Huawei smartphones have slightly different procedure of entering the Fastboot mode:


Huawei U8180

  1. Switch the device OFF
  2. Remove the battery and hold it removed for 10 seconds, then place it back
  3. Press and hold down Vol -, Menu and Power buttons simultaneously until your phone completely freezes

Huawei U8110, U8150, U8160, U8220, U8230, U8350, UM840, U8500

  1. Switch the device OFF
  2. Remove the battery and hold it removed for 10 seconds, then place it back
  3. Press and hold down Vol -, End Call (Red) and Power buttons simultaneously till your phone completely freezes

Huawei U8151, U8510, U8600, U8650, U8652, U8655, U8666, U8815, U8816, U8818, U8665, U8825D, U8833, U8950, U8950D, U8951, U8951D

  1. Switch the device OFF
  2. Remove the battery and hold it removed for 10 seconds, then place it back
  3. Press and hold down Vol - and Power buttons simultaneously till your phone completely freezes

When the phone is in "Download mode" you need to connect it to computer and install required driver (only if the phone is connected for the first time).

ADB Mode

  • Remove SIM card and then power the phone ON.
  • Enable USB debugging on the device;
    • Android 2.3: Settings > Applications > Development menu;
    • Android 4.0: Settings > Developer options
    • Android 4.2.2: Settings > About phone > Build number > Developer options
  • Connect the phone to PC and install ADB driver for your device.
  • Root the smartphone.
    • We recommend using Vroot or Kingo solution to root your device.
  • Restart the smartphone after rooting has been completed.

Unlock:

Direct unlock

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Set the phone either to Fastboot or to Download mode (procedure is explained in the Fastboot / Download mode manuals)
  5. Connect your device to PC with USB cable
  6. Install required Huawei smartphone driver (only if the phone is connected for the first time)
  7. Select required Interface in the ports selection tab:
    • Fastboot mode: Phone will be detected as Android Sooner Single ADB Interface in device manager
    • Download mode: Phone will be detected as DBAdapter Reserved Interface in device manager
  8. Press "Unlock" button

IMPORTANT! All smartphones should be connected to PC's USB 2.0 port directly. Run Sigma Software as Administrator in order to work with Huawei Android smartphones.
Kyivstar Terra and Aqua: unlock works with factory firmware only.


Phones with the locked bootloader: during Direct (Service Provider) Unlock procedure using Download Mode connection, bootloader of this phone will be unlocked automatically.

Direct unlock via ADB mode (phone in turned on state)

It's mandatory to root device before unlock!

  1. Turn the rooted phone ON and wait until it fully starts up
  2. Connect the phone to PC using USB cable
  3. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  4. "Phone model" dropdown box has to be set to "Autodetect"
  5. Go to "Unlock" tab
  6. Select "Adb interface" in the ports selection tab
  7. Press "Unlock" button
  8. The message "Unlock done… OK" indicates that procedure was completed successfully
  9. Disconnect the handset
  10. Phone is unlocked

Get unlock codes

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Set the phone either to Fastboot or to Download mode (procedure is explained in the Fastboot / Download mode manuals)
  5. Connect your device to PC with USB cable
  6. Install required Huawei smartphone driver (only if the phone is connected for the first time):
  7. Select required Interface in the ports selection tab:
    • Fastboot mode: Phone is detected as Android Sooner Single ADB Interface
    • Download mode: Phone is detected as DBAdapter Reserved Interface
  8. Press "Get Unlock Codes" button

For Huawei smartphones Sigma doesn't show unlock codes. It shows Lock Status and a number of available code entry attempts near each type of code.
Closed lock: active unlock code
Open lock: inactive unlock code

Direct unlock for U8520, U9000

  1. Install required drivers (only if the phone is connected for the first time):
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Go to "Unlock" tab
  5. Set the phone to Download mode
    1. Power the phone off
    2. Press Vol + and Power ON simultaneously
  6. Connect your device to PC with USB cable
  7. Select Diagnostics Interface / Diag port in the ports selection tab
  8. Press "Unlock" button

Read unlock codes for U8520, U9000

  1. Install required drivers (only if the phone is connected for the first time):
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Go to "Unlock" tab
  5. Set the phone to Download mode
    1. Power the phone off
    2. Press Vol + and Power ON simultaneously
  6. Select Diagnostics Interface / Diag port in the ports selection tab
  7. Press "Get unlock codes" button
  8. Message "Reading Unlock Codes… OK" indicates that procedure was completed successfully
  9. Disconnect the handset

How to enter Read Codes

  1. Turn the phone on with the non-original SIM card inserted
  2. Phone's menu will pop-up with unlock code request
  3. Enter the code that was read by Sigma Software

Direct unlock for U8850

  1. Install required drivers for Huawei U8850 (only if the phone is connected for the first time)
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Go to "Unlock" tab
  5. Connect the phone to PC with USB cable either in Normal or in Download mode connection:
    1. Normal mode: turn the phone ON and wait until it fully powers on
    2. Download mode (for SoftBank 007HW model): Press Vol + and Power ON simultaneously until you see a message that you are now in a Download mode
  6. Select Huawei Diagnostic Port in the ports selection tab
  7. Press "Unlock" button
  8. Message "Unlocking phone… Done" indicates that procedure was completed successfully
  9. Disconnect the handset
  10. Phone is unlocked

Read Unlock Codes for U8850

  1. Install required drivers for Huawei U8850 (only if the phone is connected for the first time)
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Go to "Unlock" tab
  5. Connect the phone to PC with USB cable either in Normal or in Download mode connection:
    1. Normal mode: turn the phone ON and wait until it fully powers on
    2. Download mode (for SoftBank 007HW model): Press Vol + and Power ON simultaneously until you see a message that you are now in a Download mode
  6. Select Huawei Diagnostic Port in the ports selection tab
  7. Press "Get unlock codes" button
  8. Message "Reading unlock codes… Done" indicates that procedure was completed successfully
  9. Disconnect the handset

Direct unlock for Mediapad S7 tablets

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Set the phone to Download mode:
    1. Power the device OFF
    2. Remove the flash card from the device
    3. S7-10X models: Press Vol+, Back and PowerOn buttons simultaneously until the device completely freezes
    4. S7-20X models: Press and hold down Vol -, Vol + buttons simultaneously, then press and hold Power until your phone completely freezes
  5. Connect your device to PC with USB cable
  6. Install required Huawei S7 Mediapad driver (only if the phone is connected for the first time)
  7. Select DBAdapter Reserved Interface in the ports selection tab
  8. Press "Unlock" button
  9. During Unlock procedure, Sigma will prompt the user to disconnect USB cable for a couple of seconds and reconnect it again
  10. The message "Unlocking phone... Done" indicates that procedure was completed successfully

Repair:

Repair IMEI

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Set the phone either to Fastboot or to Download mode (procedure is explained in the Fastboot / Download mode manuals)
  5. Connect your device to PC with USB cable
  6. Install required Huawei smartphone driver (only if the phone is connected for the first time):
  7. Select required Interface in the ports selection tab:
    • Fastboot mode: Phone will be detected as Android Sooner Single ADB Interface in device manager
    • Download mode: Phone will be detected as DBAdapter Reserved Interface in device manager
  8. Enter IMEI number in the "Phone IMEI" field
  9. Press "Repair IMEI" button
  10. The message "Done" indicates that procedure was completed successfully
  11. Disconnect the handset, remove and reinstall the battery

IMPORTANT! All smartphones should be connected to PC's USB 2.0 port directly. Run Sigma Software as Administrator in order to work with Huawei Android smartphones.
Kyivstar Terra and Aqua: Repair IMEI works with factory firmware only.

Repair IMEI for U8520, U9000

  1. Install required drivers (only if the phone is connected for the first time):
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Go to "IMEI" tab
  5. Set the phone to Download mode
    1. Power the phone off
    2. Press Vol + and Power ON simultaneously
  6. Connect your device to PC with USB cable
  7. Select Diagnostics Interface / Diag port in the ports selection tab
  8. Enter IMEI number in the "Phone IMEI" field
  9. Press "Repair IMEI" button
  10. Message "Done" indicates that procedure was completed successfully
  11. Disconnect the handset

Repair IMEI for U8850

  1. Install required drivers for Huawei U8850 (only if the phone is connected for the first time)
  2. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Go to "IMEI" tab
  5. Connect the phone to PC with USB cable either in Normal or in Download mode connection:
    1. Normal mode: turn the phone ON and wait until it fully powers on
    2. Download mode (for SoftBank 007HW model): Press Vol + and Power ON simultaneously until you see a message that you are now in a Download mode
  6. Select Huawei Diagnostic Port in the ports selection tab
  7. Enter IMEI number in the "Phone IMEI" field
  8. Press "Repair IMEI" button
  9. Message "Done" indicates that procedure was completed successfully
  10. Disconnect the handset

Repair damaged security area / allow firmware downgrading

User agreement:

This option is introduced for advanced users that have clear understanding what they do with the phone during all stages of repair.

Procedure:

The operation takes 4 steps:

  1. Restore security data file:
  2. Flash original firmware file for your model: Battery should be minimum 50% charged before re-flashing!
    • Download flash file either from file area at boot-loader.com -> Huawei ->, or from another trusted source.
    • Copy entire dload folder (with update.app in it) to the root directory of the MICRO SD card and flash it accordingly to the manual that is packed with each flash file as pdf document.
  3. Validate upgrade:
    You MUST perform all the above actions due to peculiarity of upgrade process of Huawei Android smartphones.
    • After upgrade, power the phone ON (if it wasn't powered ON automatically)
    • Dial *#06# and check phone's IMEI - it should be 11111111111111
    • DON'T power the phone OFF and leave it in this state for 10 minutes
    • Power the phone OFF, remove the battery and wait for 1-2 minutes; install it back into the phone and fully power it ON once again
    • Dial *#06# and:
      • if IMEI is still "11111111111111", go to stage 4
      • if IMEI is "0", return to stage 2, and on the stage 3 increase time when the phone should be in powered ON state to 15-30 min.
  4. Repair IMEI of the phone
    After 3 above stages, IMEI of the phone will remain blank, so you need to restore it. Use the general IMEI Repair manual for Huawei smartphones for it.

Known problems and solutions (KPNS):

  • No repair file for my model: Save Huawei security area from the fully working phone (Qualcomm -> service tab of Sigma) and send it to us for the analysis
  • WI-FI don't work or Notification/status bar missing: repeat the procedure, but use another provider data that corresponds with the firmware file you are flashing
  • IMEI is null/blank or can not connect to WI-FI signal: repeat the procedure with paying more attention to the "Stage 3"
  • What carrier's settings to use: Watch this video tutorial explaining how to find out what carrier's settings are in your current phone's firmware. These carrier's settings can be changed after re-flashing the smartphone with another firmware version

Work with bootloader:

Download mode:

Get Huawei bootloader unlocking password

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Service" tab
  4. Set the phone to Download mode (procedure is explained in the Download mode manual)
  5. Connect your device to PC with USB cable
  6. Install required Huawei smartphone driver (only if the phone is connected for the first time)
  7. Select DBAdapter Reserved Interface in the ports selection tab
  8. Press "Get Huawei bootloader password" button
  9. Readed password will be shown in the log window

IMPORTANT! All smartphones should be connected to PC's USB 2.0 port directly. Run Sigma Software as Administrator in order to work with Huawei Android smartphones.


Unlock Huawei bootloader

  1. "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Service" tab
  4. Set the phone to Download mode (procedure is explained in the Download mode manual)
  5. Connect your device to PC with USB cable
  6. Install required Huawei smartphone driver (only if the phone is connected for the first time)
  7. Select DBAdapter Reserved Interface in the ports selection tab
  8. Press "Unlock Huawei bootloader" button
  9. The message "Done" indicates that procedure was completed successfully
  10. Disconnect the handset, remove and reinstall the battery

IMPORTANT! All smartphones should be connected to PC's USB 2.0 port directly. Run Sigma Software as Administrator in order to work with Huawei Android smartphones.

ADB mode:

Unlock Huawei bootloader

It's mandatory to root device before unlock!

Unlocking of bootloader:

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Service" tab
  4. Power the phone ON and wait until it starts completely
  5. Make sure that USB debugging is enabled on your device
  6. Connect your device to PC with USB cable
  7. Install required Huawei ADB driver (only if the phone is connected for the first time)
  8. Select ADB Android Interface in the ports selection tab
  9. Press "Unlock Huawei bootloader" button
  10. The message "Done" indicates that procedure was completed successfully
  11. Disconnect the handset, remove and insert the battery

Get Huawei bootloader password

It's mandatory to root device before unlock!

Getting the password:

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Service" tab
  4. Power the phone ON and wait until it starts completely
  5. Make sure that USB debugging is enabled on your device
  6. Connect your device to PC with USB cable
  7. Install required Huawei ADB driver (only if the phone is connected for the first time)
  8. Select ADB Android Interface in the ports selection tab
  9. Press "Get Huawei bootloader password" button
  10. Read password will be shown in the log window

Also you can get bootloader password at the official Huawei website here and here.

Video instructions

Huawei Phones

Direct Unlock

You need to choose the model manually from the "Phone model" list. The list is located near the ports selection menu.

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. Select model from the "Phone model" list
  4. Connect the phone to PC with USB cable in the appropriate mode; connection details for each separate model are described in the "How to connect the phone" manual:
    • DOWNLOAD MODE: power the phone OFF. , press * 0 # simultaneously and while holding these buttons insert USB cable
    • NORMAL MODE: power the phone ON and insert USB cable
  5. Install required Huawei phone USB driver (only if the phone is connected for the first time):
    • DOWNLOAD MODE connection: install drivers manually
    • NORMAL MODE connection: when you connect the phone for the first time, it will install required drivers automatically; make sure that AutoRun feature is enabled on your PC
  6. Select "PC UI Interface" in the ports selection tab
  7. Press "Direct Unlock" button
  8. In case of unlock software prompting to disconnect USB cable from the phone for 3 seconds and connect it once again, please do so. But don't touch the battery.
  9. The message "Unlocking phone... Done" indicates that procedure was completed successfully
  10. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can disconnect the phone

How to connect the phone (in Download or Normal mode)?

DOWNLOAD MODE connection: power the phone OFF, press *0# simultaneously and while holding these buttons insert USB cable


Connect these models in the special mode:


Huawei:

  • U1000, U100S
  • U120, U121, U1220
  • U1205, U1211, U1215
  • U1300, U1310
  • U3300, U3310, U3311
  • U5700, U5707, U5075
  • U7200 U7300, U7310, U7315

Vodafone:

  • V710 V715, V716, V720, V725, V810, V830, V830i

NORMAL MODE connection: power the phone ON and insert USB cable


Connect these models in the powered on state:


Huawei:

  • U1250, U1251, U1270, U1280, U1285
  • U2800, U2801
  • U3100, U3220
  • U5110
  • U5900
  • U6150
  • U7510, U7510S, U7517, U7519, U7520
  • U9130

Vodafone:

  • Vodafone 736, 840

Motorola:

  • EX300

Video instructions

Acer Android Smartphones

Direct Unlock

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. How to connect different Acer smartphones:
    • Acer E210, E140, E310, E320, E400, S500: Power the phone ON and connect the phone to PC with USB cable
    • Acer S100: Power the phone OFF. Press and hold Vol- and Camera buttons simultaneously and insert USB cable
    • Acer S120, S300: Power the phone OFF. Press and hold Camera and Vol+ keys simultaneously and while holding these buttons, press Power On. The Camera key has two notches, you need to press fully.
  5. Install required Acer USB Driver for your model. Drivers can also be downloaded from the official Acer support page
  6. Select DIAG (Diagnostic) Port in the ports selection tab
  7. Press "Unlock" button
  8. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. Duding the extended heuristic method operation the phone will be restarted, so please wait till the process is completed. In the end of heuristic unlock mode procedure, please send the log file to our support.

Get Unlock Codes

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. How to connect different Acer smartphones:
    • Acer E210, E140, E310, E320, E400: Power the phone ON and connect the phone to PC with USB cable
    • Acer S100: Power the phone OFF. Press and hold Vol- and Camera buttons simultaneously and insert USB cable
    • Acer S120: Power the phone OFF. Press and hold Camera and Vol+ keys simultaneously and while holding these buttons, press Power On. The Camera key has two notches, you need to press fully.
  5. Install required Acer USB Driver for your model. Drivers can also be downloaded from the official Acer support page
  6. Select DIAG (Diagnostic) Port in the ports selection tab
  7. Press "Get unlock codes" button
  8. Message "Reading unlock codes… Done" indicates that procedure was completed successfully
  9. Disconnect the handset
    How to enter codes:
    • Turn the phone on with non-original SIM card inserted
    • Phone's menu will pop-up with unlock code request
    • Enter a code that was read by Sigma Software

* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. Duding the extended heuristic method operation the phone will be restarted, so please wait till the process is completed. In the end of heuristic unlock mode procedure, please send the log file to our support.

Video instructions

Other devices:

Direct unlock for Bmobile QW130

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. "Phone model" dropdown box has to be set to "Bmobile QW130"
  4. Connect turned ON phone to PC with USB cable
  5. Install required Bmobile QW130 Driver (only if the phone is connected for the first time); in some cases drivers can be installed automatically
  6. Select USB Diagnostic Port in the ports selection tab
  7. Press "Unlock" button

Direct unlock for SkypePhone AMOI WP-S1

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. "Phone model" dropdown box has to be set to "Autodetect"
  4. Connect turned ON phone to PC with USB cable
  5. Install required drivers (only if the phone is connected for the first time)
  6. Select USB Diagnostic Port in the ports selection tab
  7. Press "Unlock" button

* In case of unknown firmware version detection, the software will suggest unlocking the phone using the heuristic method. In the end of heuristic unlock mode procedure, please send the log file to support.

Direct unlock for ZTE hotspot mobile devices

You need to choose the model manually from the "Phone model" list. The list is located near the ports selection menu

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "Unlock" tab
  3. Select device model from the "Phone model" list
  4. Connect the device to PC with USB cable
  5. Power the device ON
  6. It can take from 30 seconds up to a minute for a device to fully start up
  7. Install required USB driver (only if the device is connected for the first time). Drivers should be installed automatically from the device; make sure that AutoRun feature is enabled on your PC
  8. Select "ZTE Diagnostic interface" in the ports selection tab
  9. Press "Direct Unlock" button
  10. The message "Unlocking phone... Done" indicates that procedure was completed successfully
  11. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can disconnect the phone

Repair IMEI for ZTE hotspot mobile devices

You need to choose the model manually from the "Phone model" list. The list is located near the ports selection menu

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. Go to "IMEI" tab
  3. Select device model from the "Phone model" list
  4. Connect the device to PC with USB cable
  5. Power the device ON
  6. It can take from 30 seconds up to a minute for a device to fully start up
  7. Install required USB driver (only if the device is connected for the first time). Drivers should be installed automatically from the device; make sure that AutoRun feature is enabled on your PC
  8. Select "ZTE Diagnostic interface" in the ports selection tab
  9. Enter IMEI number in the "Phone IMEI" field
  10. Press "Repair IMEI" button
  11. The message "Done" indicates that procedure was completed successfully

Direct unlock for BLU Dash 3.5 (D160A) / Tecno P3

  1. Select "Qualcomm" platform from the tab menu in the upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "Unlock" tab
  4. Turn the phone on without sim card
  5. Connect the phone to PC with USB cable
  6. Install USB Host Driver
  7. Select Qualcomm DIAG (Diagnostic) Port in the ports selection tab
  8. Press "Unlock" button
  9. Wait for the message "Restarting phone... Done" to appear in Sigma dialog window; only after that you can turn the phone off

Repair IMEI for BLU Dash 3.5 (D160A) / Tecno P3

  1. Select "Qualcomm" platform from the tab menu in upper left side of the software
  2. "Phone model" dropdown box has to be set to "Autodetect"
  3. Go to "IMEI" tab
  4. Turn the phone on without sim card
  5. Connect the phone to PC with USB cable
  6. Install USB Host Driver
  7. Select Qualcomm DIAG (Diagnostic) Port in the ports selection tab
  8. Enter IMEI number in the "Phone IMEI" field
  9. Press "Repair IMEI" button
  10. The message "Done" indicates that procedure was completed successfully

Video instructions

+93Afghanistan+355Albania+213Algeria+1684American Samoa+376Andorra+244Angola+1264Anguilla+672Antarctica+1268Antigua And Barbuda+54Argentina+374Armenia+297Aruba+61Australia+43Austria+994Azerbaijan+1242Bahamas+973Bahrain+880Bangladesh+1246Barbados+375Belarus+32Belgium+501Belize+229Benin+1441Bermuda+975Bhutan+591Bolivia, Plurinational State Of+387Bosnia And Herzegovina+267Botswana+55Bouvet Island+55Brazil+246British Indian Ocean Territory+673Brunei Darussalam+359Bulgaria+226Burkina Faso+257Burundi+855Cambodia+237Cameroon+1Canada+34Canary Islands, The+238Cape Verde+1345Cayman Islands+236Central African Republic+235Chad+56Chile+86China+61Christmas Island+61Cocos (Keeling) Islands+57Colombia+269Comoros+242Congo+243Congo, The Democratic Republic Of The+682Cook Islands+506Costa Rica+225Cote D'Ivoire+385Croatia+53Cuba+357Cyprus+420Czech Republic+45Denmark+253Djibouti+1767Dominica+1829Dominican Republic+593Ecuador+20Egypt+503El Salvador+240Equatorial Guinea+291Eritrea+372Estonia+251Ethiopia+500Falkland Islands (Malvinas)+298Faroe Islands+679Fiji+358Finland+33France+594French Guiana+689French Polynesia+1689French Southern Territories+241Gabon+220Gambia+995Georgia+49Germany+233Ghana+350Gibraltar+30Greece+299Greenland+1473Grenada+590Guadeloupe+1671Guam+502Guatemala+44Guernsey+224Guinea+245Guinea-Bissau+592Guyana+509Haiti+0Heard Island And Mcdonald Islands+504Honduras+852Hong Kong+36Hungary+354Iceland+91India+62Indonesia+98Iran, Islamic Republic Of+964Iraq+353Ireland+44Isle Of Man+972Israel+39Italy+1876Jamaica+81Japan+44Jersey+962Jordan+76Kazakhstan+254Kenya+686Kiribati+850Korea, Democratic People'S Republic Of+82Korea, Republic Of+381Kosovo+965Kuwait+996Kyrgyzstan+358land Islands+856Lao People'S Democratic Republic+371Latvia+961Lebanon+266Lesotho+231Liberia+218Libyan Arab Jamahiriya+423Liechtenstein+370Lithuania+352Luxembourg+853Macao+389Macedonia, The Former Yugoslav Republic Of+261Madagascar+265Malawi+60Malaysia+960Maldives+223Mali+356Malta+692Marshall Islands+596Martinique+222Mauritania+230Mauritius+262Mayotte+52Mexico+691Micronesia, Federated States Of+373Moldova, Republic Of+377Monaco+976Mongolia+382Montenegro+1664Montserrat+212Morocco+258Mozambique+95Myanmar+264Namibia+674Nauru+977Nepal+31Netherlands+599Netherlands Antilles+599Netherlands Antilles (Bonaire)+599Netherlands Antilles (Curacao)+687New Caledonia+64New Zealand+505Nicaragua+227Niger+234Nigeria+683Niue+672Norfolk Island+1670Northern Mariana Islands+1670Northern Mariana Islands (Saipan)+47Norway+968Oman+92Pakistan+680Palau+970Palestinian Territory, Occupied+507Panama+675Papua New Guinea+595Paraguay+51Peru+63Philippines+64Pitcairn+48Poland+351Portugal+1787Puerto Rico+974Qatar+40Romania+7Russian Federation, The+250Rwanda+262Réunion+590Saint Barthlemy+290Saint Helena+1869Saint Kitts And Nevis+1758Saint Lucia+590Saint Martin+508Saint Pierre And Miquelon+1784Saint Vincent And The Grenadines+685Samoa+378San Marino+239Sao Tome And Principe+966Saudi Arabia+221Senegal+381Serbia+248Seychelles+232Sierra Leone+65Singapore+421Slovakia+386Slovenia+677Solomon Islands+252Somalia+27South Africa+500South Georgia And The South Sandwich Islands+34Spain+94Sri Lanka+249Sudan+597Suriname+47Svalbard And Jan Mayen+268Swaziland+46Sweden+41Switzerland+963Syrian Arab Republic+886Taiwan, Province Of China+992Tajikistan+255Tanzania, United Republic Of+66Thailand+670Timor-Leste+228Togo+690Tokelau+676Tonga+1868Trinidad And Tobago+216Tunisia+90Turkey+993Turkmenistan+1649Turks And Caicos Islands+688Tuvalu+256Uganda+380Ukraine+971United Arab Emirates+44United Kingdom+1United States+699United States Minor Outlying Islands+598Uruguay+998Uzbekistan+678Vanuatu+379Vatican+58Venezuela, Bolivarian Republic Of+84Viet Nam+1284Virgin Islands, British+1340Virgin Islands, U.S.+681Wallis And Futuna+212Western Sahara+967Yemen+260Zambia+263Zimbabwe